抗倍特板為乙烯基酯樹脂是由雙酚型或酚醛型環氧樹脂與甲基丙烯酸反應得到的一類變性環氧樹脂，通常被稱為乙烯基酯、樹脂，別名環氧丙烯酸樹脂，為熱固性樹脂。接下來富美家抗倍特廠家根據多年的生產安裝經驗為大家介紹抗倍特板施工時應該注意哪些。

Vinyl ester resin is a modified epoxy resin obtained by the reaction of bisphenol or phenolic epoxy resin with methacrylic acid. It is usually called vinyl ester, resin, also known as epoxy acrylic resin, and thermosetting resin. Next, according to many years of production and installation experience, Fumeijia Anti-Biot manufacturer will introduce what should be paid attention to during the construction of Anti-Biot plate.

一、將泛水墊圈套入螺絲內以后，用電鉆鎖入檁條內，即完成抗倍特板的固定工作。

1、 After inserting the flashing washer into the screw, lock it into the purlin with an electric drill, and then complete the fixation of the anti-magnification plate.

二、抗倍特板在固定前先導孔，孔徑要大于固定螺絲直徑的6-9mm,以作為熱脹冷縮之用。

2、 The diameter of the pilot hole of the anti-magnification plate before fixing shall be 6-9mm larger than the diameter of the fixing screw for the purpose of thermal expansion and cold contraction.

三、抗倍特板與鋼板在縱向搭接時，要有200mm的重疊，并貼置兩條止水帶。

3、 When the anti-magnification plate and steel plate are overlapped longitudinally, there should be 200mm overlap, and two waterstops should be pasted.

四、抗倍特板固定時，要使用良好的泛水墊圈，使之介于螺絲與抗倍特板之間，以便于防水防塵。

4、 When fixing the anti-multiplier plate, good flashing washer shall be used to make it between the screw and the anti-multiplier plate, so as to prevent water and dust.

五、鋪設完畢以后，預留出抗倍特板的位置，施工由檐口逐步往屋脊方向進行?？贡短匕逯苯涌墼阡摪宓膫?cè)波峰上。

5、 After the laying is completed, the position of the anti-magnification plate shall be reserved, and the construction shall be carried out gradually from the cornice to the ridge direction. The anti-magnification plate is directly buckled on the side wave crest of the steel plate.

六、抗倍特板施工時，嚴禁腳直接踩在波峰上，以免抗倍特板開裂。要在抗倍特板的橫向位置，放置一塊1200mmx300mm{長x寬）防滑厚木板，腳踩在其上進行抗倍特板的導孔和固定螺絲工作。

6、 During the construction of the anti-multiplier plate, it is strictly forbidden to step on the wave crest directly to avoid cracking of the anti-multiplier plate. Place a 1200mmx300mm (length x width) anti-skid thick plank at the transverse position of the anti-magnification plate, and step on it to conduct the guide hole and fixing screw work of the anti-magnification plate.

抗倍特板施工的注意事項是抗倍特板固定時，要使用良好的泛水墊圈，使之介于螺絲與抗倍特板之間，以便于防水防塵。那么在對抗倍特板施工時，一定要注意以上這些。更多相關內容就來我們網站http://進行咨詢吧！

The precautions for the construction of the anti-multiplier plate are to use a good flashing washer between the screw and the anti-multiplier plate when the anti-multiplier plate is fixed, so as to prevent water and dust. Then, when constructing the double plate, we must pay attention to the above. Come to our website for more relevant content http:// Consult!